Sialic Acid Assay Kit, BioAssay™, Colorimetric/Fluorometric, High Sensitivity

Referentie S1013-31Q-96T

Formaat : 96Tests

Merk : US Biological

Meer informatie aanvragen

Neem contact op met een lokale distributeur :


Telefoonnummer : +1 850 650 7790


S1013-31Q Sialic Acid Assay Kit, BioAssay™, Colorimetric/Fluorometric, High Sensitivity

Clone Type
Polyclonal
Shipping Temp
Dry Ice
Storage Temp
-20°C

Sialic Acid is a general name for nine carbon acidic sugars with N- or O-substituted derivatives. The most common member of these sugars is N-acetylneuraminic acid (NANA). Sialic acid is widely distributed throughout mammalian tissues and fluids including serum. Sialylated oligosaccharides have been shown to exhibit antiviral properties and are also known to influence blood coagulation and cholesterol levels. The Sialic acid level in body fluids is also an important marker for diagnosing cancer.||Simple, direct and automation-ready procedures for measuring sialic acid concentrations find wide applications in research and drug discovery. Sialic acid assay uses a single Working Reagent that combines NANA aldolase, pyruvate oxidase and hydrogen peroxide determination in one step. The color intensity of the reaction product at 570nm or fluorescence intensity at lem/ex=585/530nm is directly proportional to sialic acid concentration in the sample.||Key Features:|Sensitive and accurate. Use as little as 10ul samples. Linear detection range in 96-well plate: 0.02 to 1mM sialic acid for Colorimetric Assay:s and 2 to 100uM for Fluorometric Assay:s. |Simple and convenient. Can detect free sialic acid by addition of a single working reagent and incubation for 60 min at room temperature or total sialic acid by pre-treating samples with a 60 min hydrolysis step.||Applications:|Direct Assays: sialic acid in biological samples.||Kit Contents:|Assay Buffer: 10ml Hydrolysis Reagent: 10ml|Enzyme: 120ul Neutralization Reagent: 5ml|Dye Reagent: 120ul Standard: 500ul 10mM Sialic Acid|Storage conditions. The kit is shipped on dry ice. Store all reagents at -20°C. Shelf life of three months after receipt.|Precautions: reagents are for research use only. Normal precautions for laboratory reagents should be exercised while using the reagents. Please refer to Material Safety Data Sheet for detailed information.||Bound Sialic Acid Hydrolysis Procedure:|Note: For measurement of free sialic acid, this procedure should be skipped.|1. Combine 20ul of sample with 80ul Hydrolysis Reagent in a microcentrifuge tube (screw cap tube is preferable) and incubate at 80°C for 60 min.|2. Allow sample to cool to room temperature and briefly centrifuge at 14000 rpm to spin down the hydrolysis mixture.|3. Add 20ul Neutralization Reagent to each hydrolysis reaction, briefly vortex to mix and briefly centrifuge at 14000 rpm to spin down the reaction. The samples are now ready for the sialic acid assay.||Colorimetric Procedure:|Note: SH-group containing reagents (e.g. mercaptoethanol, DTT) may interfere with this assay and should be avoided in sample preparation.|1. Equilibrate all components to room temperature. Prepare a 1mM Standard Premix by mixing 50ul of the 10mM Standard and 450ul dH2O. Dilute Standard in distilled water as follows.|No Premix+H2O Vol (ul) Sialic Acid (mM)|1 100ul+0ul 100 1.0|2 60ul+40ul 100 0.6|3 30ul+70ul 100 0.3|4 0ul+100ul 100 0|Transfer 10ul standards and 10ul samples into separate wells of a clear flat-bottom 96-well plate.|2. For each reaction well, mix 93ul Assay Buffer, 1ul Dye Reagent and 1ul Enzyme in a clean tube. Transfer 90ul Working Reagent into each assay well. Tap plate to mix. Freeze unused reagents for future use.|3. Incubate 60 min at room temperature. Read optical density at 570nm (550-585nm). Note: if the Sample OD is higher than the Standard OD at 1mM, dilute sample in water and repeat the assay. Multiply result by the dilution factor.||Calculation:|Subtract blank OD (water, #4) from the standard OD values and plot the OD against standard concentrations. Determine the slope using linear regression fitting. The sialic acid concentration of a Sample is calculated as|[Sialic Acid] =|ODSAMPLE–ODH2O|Slope X n (mM)|where ODSAMPLE and ODH2O are the optical density values of the sample and water, Slope is the slope of the standard curve inmM-1 and n is the dilution factor of the sample (n=6 for hydrolyzed samples and n=1 for free Sialic Acid samples).|Conversions: 1mM NANA equals 30.9 mg/dL or 309 ppm.||Fluorometric Procedure:|1. For Fluorometric Assay:s, the linear detection range is 2 to 100uM sialic acid. Dilute the Standards prepared in Colorimetric Procedure: 1:10 in H2O. Transfer 10ul standards and 10ul samples into separate wells of a black 96-well plate.|2. Add 90ul Working Reagent (see Colorimetric Procedure:). Tap plate to mix.|3. Incubate 60 min at room temperature and read fluorescence at lex=530nm and lem=585nm. If assays in 384-well plate are desired, use 5ul Standards and 45ul Working Reagent. The sialic acid concentration of a Sample is calculated as|[Sialic Acid] =|FSAMPLE–FH2O|Slope X n (uM)|where FSAMPLE and FH2O are the fluorescence values of the sample and water, Slope is the slope of the standard curve inuM-1 and n is the dilution factor of the sample (n=6 for hydrolyzed samples and n=1 for free Sialic Acid samples).||Materials Required, But Not Provided:|Pipeting devices, centrifuge tubes, Clear flat-bottom 96-well plates, black 96-well or 384-well plates (e.g. Corning Costar) and plate reader.

Applications
Important Note: This product as supplied is intended for research use only, not for use in human, therapeutic or diagnostic applications without the expressed written authorization of United States Biological.
References
1. Sugahara, K. et al. (1980). Enzymatic Assay of Serum Sialic Acid. Clinica Chimica Acta 108: 493-8.|2. Simpson, H. et al. (1993). Serum sialic acid enzymatic assay based on microtitre plates: application for measuring capillary serum sialic acid concentrations. Br J Biomed Sci. 50: 164-7.